Match Point ColorBody™ Porcelain
TruEdge products mean each tile is rectified and modular, which allows for the use of smaller grout joints and even more design flexibility.
Indicates products suitable for exterior applications.
Indicates product is certified by the Porcelain Tile Certification Agency. Daltile is committed to providing only the highest quality porcelain products. Every porcelain product we offer has been certified - or is in the process of being certified - by the PTCA.
Roll over to zoom product
Photo features Match Point in Jet Black and Pure White on the floor. As seen on Extreme Makeover Home Edition, Season 9.
The color saturation of this product is affected by the surface finish. The unpolished and polished finish coordinate but are not an exact match in color tone.
|Unpolished||> 0.42||<0.5%||>450 lbs.||8.0||Resistant||N/A|
|Polished||< 0.42||< 0.5%||>450 lbs.||8.0||Resistant||N/A|
A DCOF value of > 0.42 is the new standard for tiles specified for commercial application in standard A137.1-2012, Section 9.6. It replaces the SCOF value of > 0.60 referenced in ASTM C1028. For more information on the correlation between the two values and about the DCOF AcuTest, click here for more information or visit the Tile Council of North America's website: www.tcnatile.com
- These tiles have a dynamic coefficient of friction less than 0.42 as measured by the DCOF AcutestTM method. Tiles with DCOF Acutest values less than .42 are not recommended for use in areas with wet or slippery conditions. If such tiles are used as a walking surface where water, ice, oil, grease and/or other substances are present, such a condition could cause a reduction in foot traction and become unexpectedly slippery resulting in a fall and personal injury. See ANSI standard A137.1 section 184.108.40.206.10, available at www.tcnatile.com/section220.127.116.11.10.html.
- Water, oil, grease, etc. create slippery conditions. Floor applicatons with exposure to these conditions require extra caution in product selection. Not for use on ramps.
- For addtional information, refer to Factors to Consider.
- Since there is a shade variation on all natural products, the tile and trim supplied for your particular installation may not match these samples. Final selection should be made from actual tiles and trim and not from tile and trim samples or color reproductions. Manufactured in accordance with ANSI A137.1 standards.
|Target DCOF wet||Tile Texture or
|Dry & Level||n/a||n/a|
|Wet & Level||≥ 0.42||Optional|
|Commercial Dining Areas||≥ 0.50||Optional|
|Pool Decking & other wet areas with minimal footwear||≥ 0.55||Required if tile size is > 3x3|
|Covered Exterior||≥ 0.60||Required if tile size is > 3x3|
|Interior Ramps, Inclines and Uncovered Exterior||≥ 0.65||Required if tile size is > 6x6|
Residential unpolished surfaces are suitable for exterior floors and walls in freezing and non-freezing climates when proper installation methods are followed.
Residential polished surfaces are suitable for exterior walls in freezing and non-freezing climates when proper installation methods are followed.
Commercial usage is suitable for exterior walls in freezing and non-freezing climates when proper installation methods are followed.
Polished surface is only suitable for Dry & Level floor applications.
|12 x 24||
(11 3/4" x 23 9/16")
(29.8 cm x 59.8 cm)
Pieces Per Carton: 8
|24 x 24||
(23 9/16" x 23 9/16")
(59.8 cm x 59.8 cm)
Pieces Per Carton: 4
|Bullnose||S-43C9||3 x 12|
Floor bullnose trim is intended to coordinate with floor field tile in the standard 90-degree installation position.