Fabrique ™ ColorBody™ Porcelain
Products can be custom cut into linear and rectangular sizes for unique designs, with straight or beveled edges in a variety of rectangular shapes. Click here for more information.
TruEdge products mean each tile is rectified and modular, which allows for the use of smaller grout joints and even more design flexibility.
Indicates the use of pre-consumer recycled material content in a product.
Indicates product is certified by the Porcelain Tile Certification Agency. Daltile is committed to providing only the highest quality porcelain products. Every porcelain product we offer has been certified - or is in the process of being certified - by the PTCA.
Roll over to zoom product
Photo features Noir Linen (Unpolished) 24 x 24 field tile on the floor and Créme Linen 12 x 24 on the wall.
Special care should be taken when grouting with dark pigmented colors. A grout release is recommended to prevent finely powdered pigments from lodging in the pores of the tile surface. Not for use on ramps.
Maintenance: Routine maintenance will keep your tile looking new for years to come. Under normal situations, the tile can cleaned using clear water with a neutral tile cleaner. Always follow-up with a rinse of clear water. No waxes or sealers are recommended for this product.
Since there are variations in all fired ceramic products, tile and trim supplied for your particular installation may not match these samples. Final color selection should be made from actual tile and trim and not from tile and trim samples or color reproductions. manufactured in accordance with ANSI A137.1 standards.
|Unpolished||> 0.42||<0.5%||>450 lbs||8||Resistant||N/A|
|Light Polished||< 0.42||<0.5%||>450 lbs||8||Resistant||N/A|
A DCOF value of > 0.42 is the new standard for tiles specified for commercial application in standard A137.1-2012, Section 9.6. It replaces the SCOF value of > 0.60 referenced in ASTM C1028. For more information on the correlation between the two values and about the DCOF AcuTest, click here for more information or visit the Tile Council of North America's website: www.tcnatile.com
- These tiles have a dynamic coefficient of friction less than 0.42 as measured by the DCOF AcutestTM method. Tiles with DCOF Acutest values less than .42 are not recommended for use in areas with wet or slippery conditions. If such tiles are used as a walking surface where water, ice, oil, grease and/or other substances are present, such a condition could cause a reduction in foot traction and become unexpectedly slippery resulting in a fall and personal injury. See ANSI standard A137.1 section 188.8.131.52.10, available at www.tcnatile.com/section184.108.40.206.10.html.
- Water, oil, grease, etc. create slippery conditions. Floor applicatons with exposure to these conditions require extra caution in product selection. Not for use on ramps.
- For addtional information, refer to Factors to Consider.
- Since there is a shade variation on all natural products, the tile and trim supplied for your particular installation may not match these samples. Final selection should be made from actual tiles and trim and not from tile and trim samples or color reproductions. Manufactured in accordance with ANSI A137.1 standards.
|Target DCOF wet||Suitable|
|Dry & Level - Interior||n/a|
|Wet & Level - Interior||≥ 0.42|
|Commercial Dining Areas||≥ 0.50|
|Exterior Applications; Pool Decking & Other Wet Areas with Minimal Footwear||≥ 0.60|
|Covered Exterior||≥ 0.60|
|Ramps & Inclines||≥ 0.65|
Unpolished suitable for residential exterior patios (excluding pool decks) and walls in freezing and non-freezing climates when proper installation methods are followed.
|2 x 2 Mosaic||
(11 3/4" x 11 3/4" Mesh-mounted sheet)
(29.8 cm x 29.8 cm)
Pieces Per Carton: 12
36 pieces/sheet Unpolished
|12 x 12 Field Tile||
(11 3/4" x 11 3/4")
(29.8 cm x 29.8 cm)
Pieces Per Carton: 11
|12 x 24 Field Tile||
(11 3/4" x 23 9/16")
(29.8 cm x 59.8 cm)
Pieces Per Carton: 8
Light Polished and
|24 x 24 Field Tile||
(23 9/16" x 23 9/16")
(59.8 cm x 59.8 cm)
Pieces Per Carton: 4
|Linear Options Size||Shape|
|2 x 24 Field Tile||
(2" x 23 9/16")
(4.67 cm x 59.8 cm)
|4 x 24 Field Tile||
(4" x 23 9/16")
(9.73 cm x 59.8 cm)
|6 x 24 Field Tile||
(6" x 23 9/16")
(14.63 cm x 59.8 cm)
|Bullnose||S-43C9||3 x 12|
Bullnose trim also available in horizontal design in Light polished & unpolished in all colors via Special Order.
Floor bullnose trim is intended to coordinate with floor field tile in the standard 90-degree installation position.